CARLO GAVAZZI WM4-96 - PROGRAMMING Uživatelský manuál stáhnout pdf (Strana 41)

CARLO GAVAZZI

CONTROLS

SERIAL COMMUNICATION PROTOCOL

WM4-96

V1 R3

Page

3.5 RTC MAPPING

ADD. BYTE VARIABLE Coding (with bit check)

4000 1 Seconds Hex value

4001 1 Minutes Hex value

4002 1 Hours Hex value

4003 1 Day of the week Hex value

4004 1 Day of the month Hex value

4005 1 Month Hex value

4006 1 Year Hex value

4007 1

4008 1

4009 1

400A 1(LSB)

XXXYYYYY

1(MSB)

Winter starting date

0101010X

400C 1(LSB)

XXXYYYYY

1(MSB)

Winter finish date

0101010X

400E 1(LSB)

XXYYYYYY

1(MSB)

End of 1

Winter period

010WWXXX

4010 1(LSB)

XXYYYYYY

1(MSB)

End of 2

Winter period

010WWXXX

4012 1(LSB)

XXYYYYYY

1(MSB)

End of 3

Winter period

010WWXXX

4014 1(LSB)

XXYYYYYY

1(MSB)

End of 4

Winter period

010WWXXX

4016 1(LSB)

XXYYYYYY

1(MSB)

End of 5

Winter period

010WWXXX

4018 1(LSB)

XXYYYYYY

1(MSB)

End of 6

Winter period

010WWXXX

401A 1(LSB)

XXYYYYYY

1(MSB)

End of 7

Winter period

010WWXXX

401C 1(LSB)

XXYYYYYY

1(MSB)

End of 8

Winter period

010WWXXX

401E 1(LSB)

XXYYYYYY

1(MSB)

End of 1

Summer period

010WWXXX

4020 1(LSB)

XXYYYYYY

1(MSB)

End of 2

Summer period

010WWXXX

4022 1(LSB)

End of 3

Summer period XXYYYYYY

1(MSB)

010WWXXX

4024 1(LSB)

XXYYYYYY

1(MSB)

End of 4

Summer period

010WWXXX

4026 1(LSB)

XXYYYYYY

1(MSB)

End of 5

Summer period

010WWXXX

4028 1(LSB)

XXYYYYYY

1(MSB)

Start Holiday

010WWXXX

402A 1(LSB)

XXYYYYYY

1(MSB)

End Holiday

010WWXXX

402C 1(LSB)

XXYYYYYY

1(MSB)

Holiday rate

010WWXXX

402E 1

NOTE: the MSB/LSB notation is used to define how the data should be reconstructed (see below).

The LSB is always sent before the MSB, in both reading and writing frames.

The first 7 bytes are relevant to the system clock. If WM4 is programmed for dual tariff or multitariff

management, the locations from 400Ah to 402Dh are to be programmed according to the following

coding.

Gross Automation (877) 268-3700 · www.carlogavazzisales.com · [email protected]

1 2 ... 36 37 38 39 40 41 42 43 44 45 46 ... 56 57

Komentáře k této Příručce

Žádné komentáře

CARLO GAVAZZI WM4-96 - PROGRAMMING Uživatelský manuál Strana 41

Komentáře k této Příručce

Související produkty a manuály pro Sítě CARLO GAVAZZI WM4-96 - PROGRAMMING