CARLO GAVAZZI G3800 X015 - CONFIGURATION SOFTWARE Uživatelský manuál Strana 76
- Strana / 78
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
76 © 2002 Carlo Gavazzi Industri A/S. All rights reserved
G 3800 X015 Configuration Software October 2002G 3800 X015 Configuration Software October 2002G 3800 X015 Configuration Software October 2002
5. Radio Modem driver
5.1. General
The Master Generator has a built-in driver for control of an external Radio Modem, which can be used to cre-
ate wireless links where no cable is available in parts of an installation. One Master Generator must be defined
as the central MGEN and up to 32 Master Generators can be defined as remote MGEN’s. The central MGEN
is continuously polling and updating the Dupline data from all remote MGEN’s via the radio modem network,
and in this way it makes the entire system operate as one big Dupline network. Apart from increased reaction
time (depending on the number of remote MGEN’s), the system will operate as if it was one Master Generator
connected to all the I/O-modules with cable. The Master Generator supports the Radio Modem type 2ASxE
and all 3AS types from the Finnish manufacturer SATEL (www.satel.fi). These are not supplied by Carlo
Gavazzi, but are available with local support worldwide. Find below an application diagram for the Radio
Modem option. Note: Analink modules cannot be used with Radio Modems.
The Radio Modem must be connected to the COM2 of the Master Generator. For serial cable pin connections,
please refer to the Master Generator datasheet. The baud rate selected for COM2 must correspond to the
baudrate used by the radio modems and the other master generators in the network.
The central MGEN must be defined for "Radio Modem central" function for COM2, while the remote MGEN’s
must be defined as "Radio modem substation". The central MGEN can be configured for the usual intelligent
functions, and it can also be connected via COM1 or the RS485 port to a PLC or PC. The remote MGEN’s,
however, cannot be configured for any intelligent function. They will simply operate as Radio Modem inter-
faces. The system can handle all types of digital, analog (incl. multiplexed) and counter values, except for
Analink values. The configuration of the Radio Modem function is performed in the menu "Edit" under "Com-
munication setup".
Gross Automation (877) 268-3700 · www.carlogavazzisales.com · [email protected]
- Configuration Software 1
- G3800 X015 1
- Table of Contents 2
- 1. Introduction 4
- 1.2.1. File menu 5
- 1.2.2. Edit menu 6
- 1.2.4. Tools menu 7
- 1.2.3. Select menu 7
- 1.2.5. Help menu 8
- 1.3. Basic Setup 10
- 2. Objects 11
- 2.2. Standard objects 12
- PManTTast_1a 13
- PManTTast_2a 13
- PMan_TToggle_1a 15
- 2.2.4. Timer/Recycler 17
- PMan_TTimer_1a 18
- PMan_TTimer_2a 19
- 2.2.5. Real-time clock 20
- 2.2.6. Master function 22
- PMan_TMaster_1a 23
- 2.3. Special objects 25
- 2.3.2. Motion detector 30
- PMan_TMotion_1a 31
- 2.4.2.2. Master functions 33
- 2.4. Alarm functions 33
- 2.4.3. ISA Alarm 34
- PMan_TISA_1a 36
- PMan_TISA_2a 37
- 2.4.4. The Smoke Alarm 39
- PMan_TSmoke_1a 42
- 2.4.5. The Intruder Alarm 44
- PMan_TBurglar_1a 48
- 2.4.6. The Water Alarm 50
- PMan_TWater_1a 53
- 2.4.7. Common Siren 55
- 2.5. Roller blind control 56
- PMan_TRollerUpD_1a 59
- 2.5.2. Roller blind master 61
- PMan_TRollerMaster_1a 63
- 2.6. Counter and Multiplexer 64
- 3. Logic Setup 68
- 3.1. Introduction 68
- 3.3 Application 69
- 3.3.1.1. Creating Setups 69
- 3.3.1.2. Mode of operation 69
- PMan_003a 70
- (only valid for G38001015) 72
- 4.1. SMS Setup 72
- 4.2 Event-based SMS messages 73
- 5. Radio Modem driver 76
Retrotec DM-2 Gauge manuály
Uživatelské manuály a uživatelské příručky pro Měřící nástroje Retrotec DM-2 Gauge.
Poskytujeme 2 manuály pdf Retrotec DM-2 Gauge ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentáře k této Příručce